Product Sections

Main Pages

New Products

Filter Flosser filter cleaner

$29.99

Filter Flosser- Provides a powerful, evenly dispersed spray that gets in between the pleats of your cartridge filter acting like a water pick. It also generates a water and air agitation action that works out the dirt deposits down deep in the cartridge.
find out more

Best Sellers

HotSpring Spa Covers - OEM Replacement Covers (LARGE)

$450.00

HotSpring Spa Covers - OEM Replacement Covers

When you order a Hot Spring cover from Pools Plus you are receiving a factory original replacement! All covers from the manufacture are UL (underwriters laboratory) listed and ASTM rated. Larger model covers use two (2) pound density foam and a heat-sealed waterproof plastic sheeting to keep moisture at bay. If you have a cover removal devise (cover lift, cover cradle, uprite, glide rite) made by Hot Spring, you will need this cover!

These devises are attached to the cover through the side into a plate built into the spa. No other manufactured spa cover can do that. Please keep this in mind when orderinig your replacement cover.

If you do not see your cover listed here, please check one of the other products below.

Please note: Sizes and Dimensions of the HotSpring covers vary from year to year, and model to model. Make sure the information you have is correct. Once the cover is ordered, it is near impossible to cancel. Contact us with any questions you may have prior to ordering.

Shipping of covers will take approximately 2-3 weeks from the factory.
find out more

Hot Spring Spa - TRI-X Filters

$51.99

HotSpring Spa - TRI-X Filters - The Tri-X filter is 3-dimensional to more effectively filtrate by depth and surface, creating a longer time between cleaning cycles by doubling your square foot area of effective filtration. Tri-X filters will fit on most 1990 to current Hot Spring spa models. Shown on some filters is the number: PN0969601

Dimensions: Diameter 6" Length 10.5" Inside Dia. 1-15/16"
find out more

BaquaSpa Oxidizer

BaquaSpa Oxidizer previously known as BaquaSpa Shock, this is a liquid oxidizer consisting of specially stabilized hydrogen peroxide. Keeps spa water sparkling clear by oxidizing organic compounds out of the water.

Available in single quarts or a 2 pack!
find out more

Pool & Spa Vacuum Cleaner

$34.99

Pool & Spa Vacuum Cleaner - Clean dirt and small debris easily with this self contained and easy to use Spa Wand. No cumbersome hoses or hookups required. Dirt and debris is captured into a stainless steel catch screen which can be easily cleaned for re-use over and over. Goes together in a snap! No tools needed! Please note: Clean out the trap after each use.
find out more

Spa Guard Enhanced Spa Shock

Spa Guard Enhanced Spa Shock is a excellent shock for chlorine or bromine spas. Like most shocking products, this has a little chlorine to keep the spa sanitary. It also contains water clarifiers to help get your spa to prestine clear!

Avilable in 2 lbs and 5 lbs containers.
find out more

Freshwater AG+ Silver Ion Sanitizer by Nature2

Freshwater AG+ Silver Ion Sanitizer is made for HotSpring Spas, by Nature 2 / Zodiac. Silver ions are one of nature's most powerful sanitizers are continuously introduced into your spa water to inhibit bacteria growth. Simply replace the cartridge every four months for on-going protection. For a chlorine free experience use SpaGuard Spa Shock to start the process of easy spa care. This cartridge is distributed for use in Watkins manufactured spas, such as Hot Spring, Tiger River, Hot Spot, and Solana models

Part Number: 71325
find out more

5 lbs Spa Guard Bromine Tablets

$45.99

Spa Guard Spa Bromine Tabs make sanitizing your spa easy. Add tabs into our slow dissolve dispenser and forget about it. The power of an organic brominating compound (BCDMH) compressed into 1-inch tablet. These tablets are acidic and may lower pH, so pH and total alkalinity should be tested frequently and adjusted as necessary. Use Brominating Tablets in a brominator or in our Floating Dispenser.
find out more

BaquaSpa Sanitizer

BaquaSpa Sanitizer is the principal chemical in the BaquaSpa Water Care System. A bromine-free, chlorine-free liquid sanitizer that provides effective control of bacteria and protects against staining and discoloration due to metals. It stores indefinitely, is highly stable in elevated temperatures, and lasts longer than bromine- or chlorine-based sanitizers.
find out more

Spa Guard Stain & Scale Control

Spa Guard Stain & Scale - Scale or calcium carbonate build-up can cause damage to your spa surface as well as your circulation system. SpaGuard Stain & Scale Control does a great job of preventing scale by introducing powerful agents that bond to problem-causing calcium ions in your spa water.

* Prevents scale formation and cloudy water due to high calcium levels
* Removes some scale buildup on spa surface
* Removes relatively fresh metal stains from spa surfaces

Available in 1 pt or 1 qt sizes.
find out more

Aqua Genie Skimmer Basket

$10.99

Aqua Genie Skimmer Basket- Same basket as the OEM just in an after market version. Comes with a small plastic handle.
find out more

FAQ's

eStore | Service Department | FAQ's

How to Acid Clean your Spa

How to acid clean your spa's plumbing lines
*This is for Hot Spring & Tiger River spas only

Materials needed: 1 gallon Muriatic Acid
Time: 5-6 hrs

1 - Remove all non-attached materials from the spa. This includes floating brominators, thermometers, toys, pillows, floor drain grate, and filters. Leave the spa filled with water.

2 - Pour the gallon of acid into the center of the spa.

3 - Over the next 4 hours, turn the jets on for ten minutes (with the Hot Spring spas, turn on the CLEAN cycle) once an hour. Each time you turn on the jets, turn the large handle diverter 90 degrees on four position spas or 180 degrees on two position spas. This will allow the acid solution to clean the jet lines. When the jets are off, the circulation lines and heater are being cleaned.

4 - After the 4 hours, turn off the power to the spa and drain the spa using the spa drains only. This will help flush out the calcium and build up from the spa plumbing lines.

5 - As the spa drains, using a water (garden) hose, rinse and wipe down the inside of the spa. Rinse thoroughly the shell, jets, moto-massage housing, and filter compartment.

6 - After the water has drained from the spa, reinstall the drain plugs and refill the spa.

7 - Once the spa is filled, turn the power back on and chemically balance the spa water.

This procedure should be done at least once a year for customers who are on well water, and as needed for those customers who use city water.

If you have any questions or concerns regarding this procedure, please ask prior to attempting this process.

Blinking Lights on a Fresh Fill HotSPring

If your 2003 or newer Hot Spring spa is blinking both the Red and Green indicator lights, the flow switch inside the heater is not registering the proper water flow to activate the heater. This can be remedied by following these steps.

- If the spa has been recently drained and refilled, it is possible to have an air pocket in the circulation line. To help eliminate this from happening, always fill the spa through the center of the GREY filter standpipe. Remove the GREY screw cap and push the hose into the GREY standpipe. Turn the hose on full force and water pressure help remove the air pocket.

- Check the filters. If the filters have not been cleaned within the past 4 to 6 weeks, remove them and clean the filters. With the filters removed, reset the spa by powering off the spa, wait 1-2 minutes and turn the power back on.

- Check the water level. If the water level is low, the circulation pump will not be able to pull in enough water to create proper flow. Keep the spa filled at least to the middle of the filter compartment. Reset the spa by powering off the spa, wait 1-2 minutes and turn the power back on.

- If none of these solve the blinking lights, please call the service department to schedule a service appointment.

How to treat white water mold in your spa

How to treat White Water Mold in a spa?

The only way to properly treat the spa system to remove (kill) the water mold is to do the following:

- Add 1oz per 250 gallons of non-foaming algaecide to the spa

- Shock the spa to increase the chlorine/bromine level up to 5.0 ppm for chlorine and 11.0 ppm for bromine. Keep the chlorine/bromine levels high for 3-5 days prior to draining the spa.

- Remove the filter(s) and clean with fresh filter/cleaner/degreaser. Soak the filters for at least 24hrs, rinse thoroughly.

- Drain the spa. Clean with a spa surface cleaner. Rinse thoroughly and refill.

- Replace cleaned or new filter(s) and start up spa.

- Test and balance the spa water keeping the chlorine or bromine levels at the higher level for one week.

This procedure should resolve the White Water Mold within the spa circulation system.

eStore | Service Department | FAQ's